How do you put a Fisher and Paykel washing machine into diagnostic mode?
How do you put a Fisher and Paykel washing machine into diagnostic mode?
Press and hold the WASH TEMP DOWN button and then the POWER button until the machine gives 2 short beeps and lights up. Release buttons when the beeps indicate diagnostic mode has been entered. The SmartDrive is now in diagnostic mode.
How do I reset my Fisher Paykel washing machine?
Factory Reset
- Turn the dial to select ‘Spin’.
- Touch and hold the ‘Delay Start’ ‘More’ , the ‘Delay Start’ ‘Less’ and ‘Options’ buttons together for 3 seconds will appear on the screen and the machine will beep.
- Your washer will now be reset to the default settings.
How do I fix E6 error on Fisher and Paykel dishwasher?
Fisher and Paykel Dishwasher Dishdrawer Error Code E6 = The first 4 program indicator lights are flashing. Error Code Cause: Flood switch activated. How To Fix: Turn the water and power off to the dishwasher and back on to try and reset. Check Flood Switch.
Why does my Fisher and Paykel dishwasher keep beeping?
The drainage hose may be blocked or kinked, or the connection to drainage pipe may be blocked. Ensure the drainage hose and connection to pipes are not blocked. Press ► once to stop the beeping, and then again to clear the fault. / ► to resume the wash program.
How do you run a diagnostic on a Fisher Paykel dishwasher?
Diagnostic Mode. With Power off, press/hold Keylock, then press Start/Pause at the same time for 5 seconds. Release the buttons when it powers-on. Press Power once.
Why is my Fisher and Paykel washing machine not draining?
Ensure the impellor located at the back of the pump filter cavity can move freely and isn’t obstructed. Ensure both the end of the drain hose and the standpipe are below 1000mm (but above 600mm) in height – any higher prevents drainage. Check the drain hose for any bockages and debris.
How do I reset my Fisher and Paykel top loader?
Why is my Fisher and Paykel not spinning?
The wash load has gone out of balance during spin….Not Spinning Properly.
| Possible Cause | What to Do |
|---|---|
| Uneven surface | Your washer should be on a level surface to prevent it moving during a cycle. Adjust the feet if required – to ensure machine is correctly leveled refer to ‘Installation Instructions’ in your User Guide. |
Why is my Fisher and Paykel dishwasher not draining?
Straighten any kinks along the hose that drains water from your DishDrawer™. If the kinks return, you may need to replace the hose. Clean the filter plate/drain filter. Aim to clean your DishDrawer™ at least once per month, including the drain filter plates.
How do I fix Fisher and Paykel dishwasher f1 error?
- Locate the drain-access filter panel on the bottom of the drawer.
- Remove the rack that sits above it.
- Pull up to lift the drain filter and remove it from the machine.
- Set the filter under the faucet to rinse it clean with cold water.
- Reinstall the filter and confirm that it sits flush with the bottom of the DishDrawer.
How do I reset my Fisher and Paykel f1 dishwasher?
Press the Power button, then press the Start button three times until the screen displays Ld. Press the Lock button again to activate the actuators. If the lid in the machine moves up and down with little to no effort, the actuators do not need replacing.
Why is my Fisher and Paykel dishwasher not working?
Ensure the dishwasher is plugged in and the power supply is turned on at the wall. Ensure the door is firmly closed. Ensure water is connected and turned on. Check the strainer and clean if necessary, it is located where the water inlet hose screws into the tap.
How to enter diagnostic mode in a Fisher Paykel dd603?
Diagnostic Mode. With Power off, press/hold Keylock, then press Start/Pause at the same time for 5 seconds. Release the buttons when it powers-on. Press Power once.
What are the specifications of a Fisher and Paykel washing machine?
Page 1 SMARTDRIVE WASHING ® MACHINE 517769 Fisher & Paykel Appliances © 2003 Reprinted July 2004… SPECIFICATIONS Electric Supply Operating Voltage 220/240V AC 50Hz Maximum Current 2.8 amps Wash Motor Electronically commutated direct drive 3 Phase brushless DC Motor.
What to do if your Fisher and Paykel washer is not turning on?
The following is a list of problems you may encounter when using this appliance and some suggestions that may help to correct the problem. If you still have problems, please contact your Fisher & Paykel trained and supported service technician. Washer not turning on. Power not switched on at the wall. Switch the power on at the wall.
What is Phase 1 of the Fisher and Paykel service manual?
Page 22 (00000101) Phase 1 – Communications Fault The Display Module has had difficulty communicating with the Motor Control Module. Primary Source: Display Module. Action: Turn off at the wall and on again after 5 seconds and try again. 1. Check connections of the 12 way harness for bad contacts, corrosion etc.
