How much does it cost to replace a washing machine valve box?

How much does it cost to replace a washing machine valve box?

Washing Machine Valve Repair Washing machines have a shutoff valve to control the water supply. The most common issue associated with a broken shutoff valve is leaking water. To repair the shutoff valve, you may need to install new bushings. The average cost to replace a washing machine valve is $100 to $225.

What is a washing machine box?

Laundry boxes are recessed into the wall behind the washing machine and provide water supply line connections and a wastewater drain. These outlets improve the look of your laundry area by hiding pipes and tidying hoses. More importantly, they provide easy shutoff valves in the event of a leak or a burst hose.

How do I know if my inlet valve is bad?

Signs that point to an inlet valve problem include leaks that fill the dishwasher when not running, the dishwasher filling too slowly when in use, or the dishwasher not filling at all. Leaks that end up outside of the dishwasher also can indicate an inlet valve problem, and this must be addressed immediately.

How much will a plumber charge to change a valve?

The cost to install a new water main shut off valve is mostly related to labor, since the materials should run less than $40. Besides material, you can pay between $175 and $250 for a plumber to complete the job.

How much does it cost to install a washer box?

Setting up a laundry space The installation cost can be $350-$600 in a space close to existing water, electricity and gas lines; connecting the space to more distant water, electricity and gas may cost $700-$2,000, depending on the amount of labor required.

How high should a washer box be mounted?

Once you’ve selected the right washing machine outlet box for your situation, it should be installed at a height where the flood level rim (or the top of the drainage outlet) is 32” to 34” above the finished floor.

What is code for washing machine drain?

2 inches
According to the Universal Plumbing Code, the standard for washing machine drain size is 2 inches. The P-trap should be between 6 and 18 inches high from the floor, while the pipe should be between 18 and 30 inches high from the floor.

Can you plug a washer into a regular outlet?

Washing machines do not typically need special electrical hookups, but some large household appliances do require 240-V outlets. Most electric stoves and dryers and some washing machines require the higher voltage to operate. Most washing machines will run on ordinary 120-V household outlets.

Can you repair water inlet valve?

There is little that you can do to repair the valve itself, but you can clean the two inlet ports to restore full water flow. You can also test the valve to determine whether it has failed. Replacing a bad valve is a simple job and must be done with parts and procedures that are specific to your washing machine model.

How do you replace a washing machine valve?

How to Replace a Washing Machine Shut-off Valve Step 1 – Unplug the Washing Machine Power Cord Step 2 – Turn off the Water Supply to the Laundry Room Step 3 – Shut off the Locate the Shut-off Valve Step 4 – Remove the Water Hoses from the Water Valve Step 5 – Open the Control Panel of the Washing Machine Step 6 – Disconnect the Wires from the Valve

How do you hook up a washing machine?

Install a washer drain hose siphon break above the 28-inch mark on the back of the washer. Cut through the drain hose above the 28-inch mark with utility shears. Insert the two plastic drain hose sleeves provided with the siphon break kit into the cut ends of the hose. Slip the kit’s hose clamps over the cut ends.

Why is my washing machine backing up?

The dishwasher, which is connected to the sink, is backing up because it’s downstream of the washing machine, and something is preventing the water from that appliance from draining. The most likely problem is a blockage in the common waste line, which could be because of soap and lint buildup.

How does a washing machine water supply valve work?

The water inlet valve has two threaded ports that are connected to hot and cold water hoses at the back of the washing machine. Each port is controlled by a solenoid valve that sends electric power to open and close the flow of hot and cold water based on settings for the wash temperature and signals from the water-level switch.